Archery Fletching Tools Jig - Adjustable Arrow Fletchings Jig Kit Straight Metal

Description: FLETCHING JIG PARAMETER: Length 7.9inch, Width 7.3inch, Height:2.8inch. Made of Stainless Steel material, quality tested and ensured for maximum durability.EASR TO USE: Easy to operate and quick set with the magnetic clamp design, Adjustable design that you can set the jig for 3 or 4 fletch, and you can adjust the angle of the feather easily.SET UP: SOPOGER improved fletching tool with magnet attach is suitable for 2-5 inch arrow fletchings and adjustable gap for arrow shafts or bolts almost all diameters (Maximum OD 9.50mm).OPERATION: The fletching Jig can be adjusted for 3 fletch or 4 fletch by screwing selection screw. (For detailed operation instructions, please refer to the Instructions and Quick Guide to Fletching at the bottom of this page)USAGE: Using the fletching tools Jig, you can remedy damaged fletchings or make your own arrows. Product Description Fletching Jig Instructions Overview: Easy Used Easy to operate and quick set magnetic clamp, Fletch 3 vanes right-wing feathers or vanes at once Seiko Production The scale made of high hardness metal is clear and not easy to deform Material Made of Stainless Steel material, quality tested and ensured for maximum durability Usage Fit for multi-material shafts or bolts (Maximum OD 9.50mm) Component Component The fletching Jig can be adjusted for standard 3 fletch or 4 fletch.You can also set the arrow nock locator from the standard setting of feather out for recurve bows to feather up for compound bows with arrow launchers fitted. IMAGE 1.A. 3 fletch selection screw IMAGE 1.B. 4 fletch selection screw IMAGE 1.C. Barrel retaining screw IMAGE 1.D. Serrated fletch locator barrel IMAGE 1.E. Plain barrel IMAGE 2.F. Magnetic location bar SOPOGER Fletching Jig How to set the jig for 3 or 4 fletch For 3 fletches, screw in screw A and screw out screw B till you get a positive 3 locations when turning barrel marked D. !! Warning !! Do not screw in screw A too far or barrel D will lock up. When this happens, do not try to force it. slacken off A until the barrel rotates. When screwing out B, do not screw out so far as to disengage the screw from the jig, as the spring and locating ball will fall out and get lost. Hexagon head C retains barrel assembly in the jig; do not slacken or remove. To set for 4 fletches all you need to do is screw in screw B and screw out screw A till the barrel locates in 4 positions. Observe warning as before. The jig comes set to the standard recurve setting of fletch out. To change the orientation of the fletch, slacken off screw D till you can set the serrated barrel E to desired position (usually about 90° clockwise for fletch up) and tighten.This can easily be set if you have an arrow in the jig that is already set for fletch up. Setting the fletch angle To set the angle that the fletchings will be glued on to the shaft, you will need to slacken off the 2 screws on the magnetic location bar F and adjust to the required position before re-tightening the screws. lf you already have a fletched arrow and you want to set the jig to match.just fit the arrow into the jig making sure that it is fully seated on the nock locator inside barrel E. Fit the clamp to the upright fletch making sure it is fully seated onto shaft. Slacken the two screws with the allen key supplied enough to allow the magnetic location bar to move and Settle in the right position, then re-tighten the 2 screws. Now you are ready to start fletching. A quick guide to fletching lf you have set the jig to match an existing arrow you will need to mark or make note of where the back of the fletch sits. With the clamp on the fletch and sitting down against the location bar as shown in photo 3 mark the clamp with a pen or marker to show where the back of the fletch sits in the clamp. Clean the shaft with a cloth dipped in warm soapy water and dry thoroughly. set the jig to the fletch, fit the fletch into the clamp, aligning the back of fletch to your mark.*Clean base of fletch,and spread a thin bead of glue evenly along the whole length of fletch foot. Locate the back of the clamp against the location bar and press firmly down onto shaft It is best to hold the arrow firmly into the jig to prevent the shaft flexing when pushing clamp down. Allow glue to dry, remove clamp, rotate barrel to next position and repeat above with your hen fletches. The screw on the clamp can be used to slacken it before removal, though it should not be necessary if the fletchings are set. Finishing your arrows when all 3 fletches are on and dry remove the arrow from the jig and Top and Tail the fletches.Topping and Tailing means to drop a (small !) blob of glue on the front and rear of the fletch.You can now call yourself a Fletcher and with practice and patience you will have professional looking arrows every time. ✓ ✓ ✓ ✓ ✓

Price: 34.87 USD

Location: Sugar Land, Texas

End Time: 2024-03-22T21:58:39.000Z

Shipping Cost: 0 USD